Zivan NG7 Manual de instrucciones descargar pdf (Pagina 3)

NG5-7-9 CAN Bus Interface

Charging curve selection

You can press the MODE button according two modalities:

1. Long pressure (at least 1 second): along the battery charger setting it means ENTER

2. Short pressure (less than 1 second): along the battery charger setting it means ROLL

Setting:

1. While pressing the MODE button light on the equipment.

ROLL:

select the

branch

type:

• 0 corresponds to a MASTER unit charger (connected with one or more SLAVES units).

• from 1 to 8 it gives the ID of the SLAVE (used together to a MASTER).

• 9 identifies a STAND-ALONE charger (used as a single unit).

3. ENTER: branch type confirmation. Next selection is choose the Battery type (Lead acid type corresponds to BA1 otherwise

Gel

corresponds to BA2).

4. ENTER: Battery type confirmation: next level is to select the Charging curve.

5. ROLL: select the desired Charging

curve.

Availability is on 4 charging curves:

a. CU1: lUla curve;

b. CU2: IUIU0 curve;

c. CU3: power supply;

d. CU4: programmable curve (eg. desulphation).

6. ENTER: Charging curve confirmation: now select the Capacity.

7. ROLL: Capacity selection.

Starting point is a nominal value and by the ROLL you can select a value included between 50% and 140% of the nominal in

steps of 10%. On the display it is shown the last capacity selected.

8. ENTER: Capacity confirmation: then you can select the Recharging time (in hours).

9. ROLL: Recharging time confirmed .

Starting from a suggested Recharging time (according to the capacity chosen at the previous step) this time can only be

increased up to 20 hours max.

10. ENTER: Recharging time confirmation: the battery charger goes to a stand-by modality waiting that the output cables being

connected to the battery binding-clamps (if connections have been done already before starting the setting, once arrived at

point 10 the charger immediately starts).

Warning: if some trouble or mistake may occur along setting procedure, switch off the battery charger by the rotary ON-OFF switch,

then switch oh again by keeping pressed the MODE button and restart setting operation from the beginning.

Alarms

When an alarm situation stopping the charge occurs, the display shows one of the information below according failure detected:

<A> <alarm code identified with a 2 digits

code> Alarm table list here following:

CODE

ALARM TYPE

DESCRIPTION

STOP

A01 LOGIC FAILURE #1 Trouble on current detection YES

A02 CAN BUS KO Trouble on CAN communication NO

A03 WATCHDOG Loqic board mis-workinq YES

A05 HIGH TEMPERATURE BATTERY Battery over temperature (>55°C) YES

A06 MISSING PHASE Phase lacking YES

A07 OVERCURRENT Over current YES

A08 HIGH TEMPERATURE Battery charter high temperature YES

A09 MISMATCH VOLTAGE Internal failure YES

A10 TIMEOUT End of Phase 1 due to timeout YES

A11 OVER DISCHARGE Over discharged Battery NO

A12 DEEP DISCHARGE Deeply discharged Battery NO

A13 BATTERY DISCONNECTED Battery disconnection white charging YES

A14 PUMP MISTAKE . Air pump mis-working NO

A15 TH. SENSOR KO Thermal sensor failure NO

Notes:

A05:

A11:

A12:

A15:

The charge restarts once the battery temperature reaches a value lower than 50 °C.

Notice on the battery status. By pressing the MODE button, a desulphation phase start followed then by the standard charge.

Notice on the battery status. The standard charge is starting anyway

With the thermal sensor out of order the battery charger behaves as if it was not equipped with by showing the A15 code on the display.

Each alarm except A02 and A13, gives also a 30' lasting audible alarm.

D01570-02

1 2 3 4 5

Comentarios a estos manuales

Sin comentarios

Zivan NG7 Manual de instrucciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Cargadores De Bateria Zivan NG7